Material Guide

Hempcrete Block R-Value: Per Inch, Per Wall, and Code Compliance

Hempcrete delivers R-2.2 per inch — confirmed by ASTM C-518 testing. A 12-inch hempcrete block wall reaches R-26, enough to meet IECC 2021 in most climate zones without added foam.

Hempcrete has an R-value of R-2.2 per inch, based on ASTM C-518 testing. A standard 12″ hempcrete block wall delivers R-26 before any interior or exterior insulation is added. The hemp hurd aggregate also provides thermal mass that slows heat transfer over time — a benefit the steady-state R-value number does not fully capture.

What Is Hempcrete?

Hempcrete is a biocomposite building material made from hemp hurd — the woody inner core of the hemp stalk — mixed with a lime-based binder. Hemp hurd is a byproduct of hemp fibre processing and has historically been treated as agricultural waste. Mixed with lime and water, it forms a lightweight, breathable material that hardens as the lime absorbs carbon dioxide from the air and gradually mineralizes.

Hempcrete blocks are pre-cast in moulds and cured before delivery to the job site. They are installed similarly to masonry blocks but are not structural — they require a separate timber or steel frame to carry roof and floor loads. The hempcrete fills the wall cavity, providing insulation, air sealing, moisture regulation, and carbon storage.

Hempcrete R-Value by Wall Thickness

Hempcrete ThicknessR-ValueNotes
6″ (150 mm)~R-13Thin wall — insufficient in Zones 5+
8″ (200 mm)~R-18Common cast-in-place thickness
10″ (250 mm)~R-22Meets IECC Zone 5 mass wall requirement
12″ (300 mm)~R-26Standard block; meets Zones 1–6
15″ (375 mm)~R-33Meets Zone 7–8 requirements

R-values are based on R-2.2 per inch from ASTM C-518 testing. Some sources cite up to R-2.5 per inch depending on hemp density and binder ratio. Use the lower figure for code compliance calculations.

Model Your Hempcrete Assembly

Add hempcrete block to your wall assembly and check it against IECC 2021 for your climate zone.

Open calculator →

Hempcrete vs. Other Insulation Materials

MaterialR-Value per InchCarbon ImpactBreathable
HempcreteR-2.2Carbon negativeYes
Closed-cell spray foamR-6 to R-7High GWPNo
Open-cell spray foamR-3.5 to R-4Moderate GWPPartially
XPS rigid foamR-5High GWPNo
EPS rigid foamR-3.8Moderate GWPNo
Fiberglass battR-3.1 to R-3.8Low GWPYes
Mineral wool battR-3.7 to R-4.2Low GWPYes
Faswall Block 8″R-1.4 avg.Low GWPPartially

Hempcrete’s R-value per inch is on the lower end compared to petroleum-based foam products, but it achieves competitive whole-wall performance through thickness rather than material density. Its carbon-sequestering properties — the wall stores carbon as the lime mineralizes — make it one of the few building materials with a net-negative carbon footprint over its life.

Does Hempcrete Meet IECC 2021 Building Code?

Hempcrete qualifies as a mass wall under IECC 2021, which means it benefits from the mass wall exception — a lower R-value requirement than framed walls, because thermal mass slows heat movement and provides performance benefits beyond what steady-state R-value measures.

IECC Climate ZoneMass Wall R-Value Required12″ Hempcrete (R-26)
Zone 1–2R-3✓ Passes
Zone 3R-5✓ Passes
Zone 4 (except Marine)R-8✓ Passes
Zone 4 Marine & Zone 5R-13✓ Passes
Zone 6R-15✓ Passes
Zone 7R-19✓ Passes
Zone 8R-19+✓ Passes

A 12″ hempcrete block wall at R-26 clears the IECC 2021 mass wall minimum in every climate zone. For Zone 7 and 8 jurisdictions with stricter local amendments, verify with your authority having jurisdiction (AHJ) before building.

IRC 2024 Appendix BL for Hempcrete

In the United States, hempcrete construction gained formal recognition in the 2024 International Residential Code (IRC) under Appendix BL. This appendix establishes requirements for non-structural hempcrete wall systems including block installation, moisture management, and structural frame requirements. Jurisdictions that adopt IRC 2024 and enable Appendix BL have a clear permitting pathway for hempcrete projects. Check whether your state or municipality has adopted IRC 2024 with Appendix BL before designing a hempcrete project.

Thermal Mass: What R-Value Misses

Hempcrete’s steady-state R-value of R-2.2 per inch understates its real-world thermal performance. Like concrete, brick, and other dense materials, hempcrete has significant thermal mass — it absorbs heat slowly during the day and releases it slowly at night, damping indoor temperature swings. This phase-shift effect is most beneficial in climates with large daily temperature swings (hot days, cool nights) where it reduces peak heating and cooling loads beyond what the R-value alone predicts.

In consistently cold climates (Zones 6 through 8), thermal mass is less beneficial because the outdoor temperature is cold most of the time. In these zones, the insulation value must carry more of the load, and hempcrete at R-2.2/in may benefit from supplemental insulation to reach effective performance.

Hempcrete Breathability and Moisture Management

One of hempcrete’s most distinctive properties is its vapour permeability. Unlike closed-cell spray foam or XPS rigid foam, hempcrete allows moisture vapour to pass through the wall assembly. This breathability means the wall can absorb and release moisture without trapping it, reducing the risk of interstitial condensation and mould growth.

Hempcrete walls should not be combined with a standard polyethylene vapour barrier on the warm side, as this would trap moisture that the hempcrete naturally wants to release. Consult a building science professional when designing hempcrete wall assemblies in cold climates — conventional vapour control strategies do not always apply.

Where Hempcrete Blocks Are Available in North America

Hempcrete blocks are still a niche product in North America compared to Europe, where manufacturers like IsoHemp produce over one million blocks per year. In the United States, Hemp and Block (Colorado) is the first dedicated American hempcrete block manufacturer, producing blocks designed to meet IRC 2024 Appendix BL. Other US-based options include cast-in-place hempcrete systems using a lime binder mixed on site with hemp hurd sourced from domestic hemp processors.

In Canada, hempcrete falls under provincial building codes, which vary in their recognition of hemp-lime construction. Always confirm the permitting pathway with your local authority having jurisdiction before specifying hempcrete.

Frequently Asked Questions

What is the R-value of hempcrete?

R-2.2 per inch, based on ASTM C-518 testing. A 12″ hempcrete block wall reaches approximately R-26. Thermal mass provides additional real-world performance beyond the steady-state R-value.

What is hempcrete made of?

Hemp hurd (the woody core of the hemp stalk) mixed with a lime-based binder. No Portland cement is used in most formulations. The lime binder gradually mineralizes by absorbing CO², giving hempcrete its carbon-sequestering properties.

Does hempcrete meet building code?

Yes, under IRC 2024 Appendix BL in jurisdictions that have adopted it. A 12″ hempcrete block (R-26) meets or exceeds IECC 2021 mass wall requirements in all climate zones. Confirm Appendix BL adoption with your local AHJ before permitting.

Is hempcrete structural?

No. Hempcrete is a non-structural insulating fill. It requires a separate wood or steel structural frame to carry roof and floor loads. The hempcrete wraps the frame and provides insulation and air control.

How does hempcrete compare to spray foam?

Closed-cell spray foam achieves R-6 to R-7 per inch — roughly three times hempcrete’s R-value per inch. However, hempcrete sequesters carbon, is vapour-permeable, and has a much lower environmental impact. For equivalent whole-wall R-value, hempcrete requires more thickness than foam.

Related Guides

Faswall Block R-Value — R-Value of Concrete Walls — R-Value for Basement Walls — Ontario Insulation Requirements — Basement Finishing Code Requirements