Alberta Building Code 2019 · Section 9.36

Alberta Insulation Requirements

Most of Alberta sits in climate zones 6 and 7 — among the coldest residential construction environments in Canada. Here are the minimum insulation requirements from the Alberta Building Code 2019.

Alberta Building Code 2019 Section 9.36 requires a minimum of RSI 8.67 (R-49) for attics, RSI 3.52 (R-20) for above-grade walls, and RSI 1.76 (R-10) for basement walls in most of the province. Requirements are expressed in RSI (metric) — multiply by 5.678 to convert to R-value.

RSI vs. R-Value: The Quick Conversion

Canadian building codes use RSI (the metric unit for thermal resistance). Product labels and field conversations in Canada often use R-value (the imperial unit). They measure the same thing in different units.

To convert: R-value = RSI × 5.678. The most common conversions for Alberta:

RSIR-Value (approx.)Typical use
RSI 1.76R-10Basement walls, slab edge
RSI 2.99R-17Some wall assemblies
RSI 3.52R-20Above-grade walls
RSI 5.29R-30Cathedral ceilings
RSI 8.67R-49Attic / ceiling with attic space

Alberta Minimum Insulation Requirements

The following requirements apply to residential construction under ABC 2019 Section 9.36. Most of Alberta falls in Heating Degree Day (HDD) zones that correspond to these requirements. Always verify with your local municipality — some areas have adopted amendments.

AssemblyMin. RSIMin. R-ValueNotes
Attic / ceiling with attic spaceRSI 8.67R-49Most common ceiling type
Cathedral ceilingRSI 5.29R-30Continuous insulation required
Above-grade wallsRSI 3.52R-20Effective assembly R-value
Basement walls (below grade)RSI 1.76R-10Full height of foundation
Heated crawl space wallsRSI 1.76R-10Same as basement walls
Exposed floor over unheated spaceRSI 4.67R-26.5Floor over crawl space or garage
Slab-on-grade edgeRSI 1.76R-10Perimeter insulation

⚠️ Verify locally: Alberta municipalities may have local amendments to the ABC 2019. Edmonton, Calgary, and other cities occasionally adopt requirements ahead of the provincial code cycle. Always confirm requirements with your local permit office before construction.

Check Your Wall Assembly

Build your assembly layer by layer and get an instant pass/fail against code minimums.

Open calculator →

Alberta's Climate Zones

Alberta spans a wide range of climates. The province is divided into Heating Degree Day (HDD) zones that determine which requirements apply. Most major population centres fall in the colder end of the range:

City / RegionApprox. HDD (18°C)Climate Zone
Lethbridge~4,000Zone 6
Calgary~4,800Zone 6–7
Edmonton~5,100Zone 7
Red Deer~5,000Zone 7
Fort McMurray~5,700Zone 7
Grande Prairie~5,500Zone 7

Meeting the R-20 Wall Requirement

The R-20 effective wall requirement is where most builders in Alberta focus their attention. A standard 2×4 wall with R-13 batt insulation falls well short. Common compliant assemblies include:

Note that the R-20 requirement is for the effective assembly R-value — not the nominal insulation value. Thermal bridging through studs reduces the effective R-value of a wall below the nominal insulation R-value. A 2×6 wall with R-19 batts achieves roughly R-16 effective due to bridging — which is why continuous exterior insulation is increasingly common in Alberta.

Basement Insulation in Alberta

The R-10 minimum for basement walls in Alberta is a floor, not a target. Given Alberta’s cold winters, many energy-conscious builders insulate to R-17 or higher below grade.

Interior basement insulation

The most common approach: rigid foam (XPS or polyiso) against the foundation wall, covered by a stud wall with batt insulation. The vapour barrier goes between the rigid foam and the stud wall in cold climates. Closed-cell spray foam applied directly to the concrete eliminates the need for a separate vapour barrier.

Exterior basement insulation

XPS rigid foam applied to the outside of the foundation before backfilling is highly effective — it keeps the concrete warm and eliminates interior thermal bridging. Common in new construction; impractical as a retrofit.

Air Sealing in Alberta

In Alberta’s climate, air leakage is often a bigger heat loss driver than insulation R-value. The ABC 2019 requires buildings to meet an air tightness standard (ACH50) tested by blower door. A well-insulated but leaky assembly can perform worse than a moderately insulated, well-sealed one. Vapour barriers double as air barriers when properly taped and sealed at penetrations.

Build Your Assembly

Layer-by-layer R-value calculator with pass/fail against Canadian and US code minimums.

Open calculator →

Frequently Asked Questions

What is the minimum attic insulation in Alberta?

RSI 8.67 (approximately R-49) for ceilings with attic space. Cathedral ceilings require RSI 5.29 (R-30).

What R-value is required for exterior walls in Alberta?

RSI 3.52 (approximately R-20) effective assembly value under ABC 2019 Section 9.36 for most of the province.

What insulation is required for a basement in Alberta?

RSI 1.76 (approximately R-10) for basement and crawl space walls. Many builders exceed this in Alberta's cold climate.

What building code applies to residential construction in Alberta?

The Alberta Building Code 2019, based on the National Building Code of Canada 2015 with Alberta-specific amendments. Energy requirements are in Part 9, Section 9.36.

Do RSI and R-value mean the same thing?

They measure the same property (thermal resistance) in different units. R-value = RSI × 5.678. RSI 3.52 = R-20. RSI 8.67 = R-49.

Is Alberta colder than Ontario for insulation purposes?

Most of Alberta is in climate zones 6–7, colder than southern Ontario (zones 5–6). Alberta's requirements are similar to Ontario's northern regions and the OBC's coldest zones.

Related Guides

Ontario Insulation Requirements — BC Insulation Requirements — What R-Value Do I Need for My Attic? — Build Code Calculator